Thursday, September 6, 2012

Hextronik MG-14 14g/2.2kg/0.11sec aircraft servo


Hextronik MG-14 Metal gear servo
MG-14
Weight: 14g
Dimension: 23*12.2*29mm
Stall torque: 2.2kg/cm(4.8V )2.5kg/cm(6V)
Operating speed: 0.11sec/60degree(4.8v), 0.10sec/60degree(6v)
Operating voltage: 4.8-6.0V
Dead band width: 10us

OrangeRx Futaba FASST Compatible 8Ch 2.4Ghz Receiver S-Spec



Compatible with Futaba FASST receivers: TM7, TM8, TM10, TM14 + more.

The OrangeRx 8ch is only 9.7g in weight and 30x45x10mm in size. Great for small planes, helis, parkflyers or even medium sized sport planes. These receivers can be used in pairs to create a satellite system with 14 channels.

Key features.
Light weight 9.7g
Compatible with FASST aircraft radio and module systems
8 Channels
Compact design 30x45x10mm
Twin antenna for diversity and long range.
Input voltage: 4~9.8V
Specified Range: 1.5km+
Resolution: 3072
Latency: 22ms
Failsafe
Up to 14 channels in satellite mode (requires 2 TFR8-S receivers)

Included.
OrangeRx Futaba FASST 2.4Ghz Compatible 8Ch receiver
2 x Jumper Plugs

All OrangeRx receivers come with a 12 month warranty.
NOTE* This is not a Futaba receiver, nor is it a copy of a Futaba receiver.
Futaba and FASST are trademarks of Futaba Co (JP).

Note* Disable failsafe on transmitter, otherwise you will experience servo jitter.

To use satellite mode you must bind both receivers to your transmitter then short the two top pins on CH1 and CH2 as show in the picture above.

TURNIGY TRUST 70A SBEC Brushless Speed Controller



Turnigy® TRUST SBEC ESCs have a very flexible and broadly capable MCU, able to run all types of brushlessmotors.
The large heatsink and simple PCB layout make heat dissapation consistant, enabling the ESC to be run at its limit, without failure.
The ESC is program-card and transmitter programmable with clear and easy to understand instructions included.
Default factory settings are;
Brake: off
Battery: LiPo Auto Detect
Low Voltage: 3.2v (power down motor)

Spec.
Max Motor Current: 70A
Max BEC Current: 3A
BEC Voltage: 5.5v (Switching)
LiPo: 2~6S
NiMH:5~16cells
Weight: 65grams

Programming Options.
Battery Type
Forward/Reverse
Soft Start
LV Setting (Ignore, Reduce Power, Stop Motor)
Timing (Auto, Med, High)
Switching (8,16kHz)
Factory Restore

NTM Prop Drive 35 Series Accessory Pack


Standard accessory pack for NTM Prop Drive 35 series motors.
CNC Machined (take a close look at the cross mount, even that is machined rather than punched) from billet 6061 alloy for strength and balance.
Produced in-house by hexTronik to reduce costs and deliver better value to you!

Shaft Diameter: 6mm
Shaft Length: 27mm
Cross Plate Bolt Holes: 42mm
Weight: 22.8g (Total)

NTM Prop Drive Series 35-36A 1400Kv / 550W




NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.

Because we design and build these motors completely in-house (from 3D/2D drawing to materials sourcing, machining, balancing, final assembly and dyno) we can completely control production and ensure product consistency from design right through to shipping the product to you. The removal of middle-men has meant we can drive better value to the market and retail these motors at factory(our) prices! All performance figures are real and tested on our own motor dynos.

Our QC engineer checks and balances each motor before shipping to the HobbyKing.com warehouse.

Specs:
Model: NTM Prop Drive 35-36A 1400
Kv: 1400rpm/v
Turns: 7
Max current: 55A
Max Power: 550W
Shaft: 4mm
Weight: 117g
ESC: 60A
Cell count: 3s~4s Lipoly
Bolt holes: 18.9mm & 25mm
Bolt thread: M3
Connection: 3.5mm Bullet-connector
Suggested Prop: 8x4 ~ 11x5.5

Prop Tests:
8x4 - 14.8v - 621W - 42A
8x4 - 11.1v - 277W - 25A
9x6 - 11.1v - 432W - 39A
10x5 - 11.1v -510W - 46A
11x5.5 - 11.1v - 543w - 49A