Tuesday, February 7, 2012

Turnigy RotoMax 100cc Size Brushless Outrunner Motor






Upgrade your 100cc size gas engine model with the Turnigy RotoMax 100cc Brushless outrunner motor. This motor will provide clean and efficient power for your large scale aircraft without the mess and hassle of fuel.

When combined with a 12s Lipoly battery, 27x12 Propeller and a 250Amp ESC the RotoMax motor will supply punchy, responsive power that only an electric setup can provide.

This motor is specifically suited for carbon fiber & wooden propellers and features an IC style 6 bolt hole design. The shaft has also been tapped to suit a 5mm bolt to make fitting a spinner of your choice easy.

Spec.
Battery: 12 Cell / 44.4V
RPM: 167kv
Max current: 170A
Watts: 7992w
No load current: 44V/4.5A
Internal resistance: 0.021 ohm
Weight: 2074g
Diameter of shaft: 10mm
Suggested ESC: 250A 12S Compatible
Suggested Prop: 27x12

Turnigy Fatboy 300A ESC 5~15S - (OPTO)







Our largest ESC yet! the Turnigy Fatboy speed controller is rated at a massive 300 Amp continuous current draw and 380 Amp burst!

The Fatboy features a large Aluminum heat sink case, twin brushless cooling fans, dual 10AWG input wires, built in anti-spark protection and 8mm female bullet terminals for the motor output.

A programming box has also been included with the Turnigy Fatboy to make setup fast and easy. This ESC is suited to large scale 100cc plus Electric conversions.

Specs.
Voltage: 18.5V-55.5V (5s-15s Lipo)
Current: 300A (380A surge within 10 seconds)
BEC: No BEC (Opto)
Size: 19cm x 12cm x 4.9cm
Weight: 850g

Programming Features.
Auto detect Lipo cells
Fully Programmable LVC
Current limiting
Cutoff type
Brake type
Timing advance
Start up type
Governor mode.

WARNING
This ESC is suited to R/C model applications only. Do not attempt to use it to power Push Bikes, Mountain boards, go-karts or similar machines. The programming logic is only designed for R/C Plane and Heli use. No warranty will be offered for incorrect use of this item.

12 Blade High-Performance 90mm EDF Ducted Fan Unit






A high thrust and well designed Electric Ducted Fan unit for high power applications, the 12 blade arrangement makes for a quiet fan unit with an amazing sound, this is the closest you will ever get to the sound of a Turbine!

Made with 30% FRP, the indivdual blades are not only able to absorb high power, high rpm motor set ups, this arrangement also allows for precise blade alignment and rotor balance. The blade locking arrangement is precise and simple to assemble, two rotor adapters are included, one for 5mm motor shafts and one for 8mm shafts, suitable motors are 36mm~39mm diameter. If you have noise concerns at your flying field or are just looking for that realistic Whoooshing sound, this is the fan for you!

Specs:
Outside Diameter: 92mm
Rotor Diameter: 89mm blade
Material: carbon fiber reinforced Nylon rotor
Shaft adaptor to motor: 5mm or 8mm
Max RPM: 45000 RPM

* Please note, some 39-40mm motors may require material to be removed from the shroud or motor casing for a perfect fit.

10 Blade High-Performance 70mm EDF Ducted Fan Unit





A high thrust and well designed Electric Ducted Fan unit for high power applications, the 10 blade arrangement makes for a quiet fan unit with an amazing sound, this is the closest you will ever get to the sound of a Turbine!

Made with 30% FRP and dynamically balanced, for use with high performance 28mm EDF motors, either 3.17m or 4mm shaft. For the best results from this fan, we reccomend the Turnigy 2855 EDF motors.

Specs:
Outside Diameter: 72mm
Rotor Diameter: 68mm blade
Meterial: carbon fiber reinforced Nylon rotor
Shaft adaptor to motor: 3.17mm or 4mm
Max RPM: 45000 RPM